KOROGI-Lab0.6.0-rc.1 (c95d233)
8 Timbres · Near / Far
GATE
TIMBRE · 1 / StandardSolid: audio · Dashed: control
COMMON SPACE
COMMON SPACE
1 2 3 4
ΣL/R
ΣL/R
LIMITER
SOURCESOSC1 = carrier / OSC2 = modulation source
OSC1 / OSC2 source controls
Gate Phase · OSC1/2 linked
OSC1 → MOD
Gate Phase · OSC1/2 linked
OSC2 → FILTER2 → MOD
OSC1 / Carrier
Global detune: -- cent → -- Hz
Voices
OSC2 / Modulator
Global detune: -- cent → -- Hz
Voices
PITCH / MODULATIONPEnv is common to OSC1/OSC2. ADSR points are percent offsets from each oscillator's base frequency. AM and FM are exclusive.
OSC2 → FILTER2 → MOD
MOD Mode / Depth
Mode
AM: OSC2 modulates OSC1 level
PEnv
FILTERSFilter1 = OSC1 audio path / Filter2 = OSC2 modulation path
4th order = two identical 2nd-order stages in series
FILTER1 / Audio Path
Type
Order
FILTER2 / Modulation Path
Stage1
Type
Order
Stage2 in series after Stage1
Type
Order
Destination
FEnv Target
AMPLITUDE ENVELOPECurve applies to Attack, Decay and Release. Gate releases on OFF; One-shot releases after Decay.
FILTER1 → AEnv → Channel Gain
AMPLITUDE ENVELOPE 2OSC2 path envelope. Sounds when FILTER2 Destination is AEnv OUT; BURST pulses also trigger it.
FILTER2 → AEnv2 → FX1
FILTER ENVELOPEIndependent signed cent envelope for Filter1.
BURSTTimbre articulation · repeat AEnv One-shot pulse groups while the phrase Gate is on.
ONE-SHOT PULSE GROUP
AEnv T: -- · Full-group guide: --
SEQUENCEPlay and record independent Gate and Pitch gestures for the selected timbre.
GATE
SONG
SongFrame
PATTERN / RECORD / PLAY
Gate
Pitch
00:00.00 / 00:30.00
New Pattern Length
→
PERFORM
Gate timelineTimbre 1 · No recording
Quantize
Quantize range 0.00 s–0.00 s
015 s30 s
Start 0.00 sEnd 30.00 sdt 30.00 s
Pitch timelineTimbre 1 · No recording
015 s30 s
Start 0.00 sEnd 30.00 sdt 30.00 s
PC: Space = Gate · Drag Pitch + Gate · Filter Amount → F1 / F2 cutoff / center
TIMBRE FX1Effect for the selected timbre
Timbre / FX1

Typical use: distortion

COMMON SPACE FX / GAINNear / Far FX2, FX3 and bus gain
Mix1 / FX2

Typical use: chorus / delay

Mix1 / FX3

Typical use: reverb

BUS GAIN
COMMON SPACE OUTPUTFinal balance and master level
OUTPUT
TIMBRE DETUNEPitch variation per timbre. Use Level in TIMBRES and Drive in FX1 for loudness and distortion.
TIMBRE · Detune
Source Detune
ri: -- / detune: -- cent
FILES / SESSIONSave or load all eight timbres and their common settings.
Session File
Status
No patch operation yet.
Use Load and Save in TIMBRES for individual timbres. Session files include all eight slots, independent Gate and Pitch Patterns, Song settings, and COMMON SPACE. New files use timbre-v21 / session-v23; supported older files can be loaded. Legacy PEnv Amount/Time is ignored on import. The header shows the latest result; tap it to open this dialog.